基于滤波器前置的三相软件锁相环设计

针对传统锁相环在电压不平衡及畸变时锁相误差大、动态响应速度慢的问题,根据软件锁相环(SPLL)的原理提出一种滑动滤波器(MAF)前置锁相环,并通过一种快速不平衡分量抑制及相位延迟补偿的方法来改善MAF性能,有效提高了锁相环的动态响应速度和锁相精度.通过MATLAB/Simulink仿真平台及TMS320F28335数字信号处理器芯片对所提出的锁相环控制策略在三相电压不平衡及电压畸变的条件下进行验证,结果表明该SPLL锁相误差小,动态响应速度快,稳定性高.     

含储能型虚拟同步发电机的直驱风机并网系统自适应协调阻尼控制策略

储能型虚拟同步发电机(VSG)的灵活控制特性能够为风电并网系统提供有效的频率和电压支撑,然而系统振荡特性会受到一定程度的影响,同时风电时变出力特性导致的运行点变化也将使得定参数阻尼控制表现出适应性不足的问题.为此,提出了适应风电出力时变特性的自适应协调阻尼控制策略.首先,在风电并网系统状态空间模型的基础上推导线性变参数模型,以直驱风机的有功功率为调度变量,根据稳定域确定运行空间范围;然后,利用间隙度量对运行空间进行划分,确定各子运行空间的典型运行点并将其作为多胞形顶点,建立调度增益与系统运行工况以及控制器的映射关系;最后,针对不同频率振荡模式协调设计自适应控制器.测试系统的仿真结果表明,所设计的自适应协调阻尼控制器不仅能够同时阻尼含储能型VSG并网系统中的次同步振荡和低频振荡,也能在风电出力大范围时变工况下保持良好的阻尼水平.     

CAN网络控制系统的网络时延分析与检测

针对CAN总线的实时特性,分析CAN网络控制系统的网络时延模型.结合CAN报文延迟时间在错误帧影响下的数学模型,分析了影响报文延迟时间的主要因素.通过所设计的CAN网络实验平台,在线检测CAN报文延迟时间,分析报文实际传输时延与理论分析的差异.实验表明错误帧及网络负载是造成较大网络时延的直接原因,进而验证了网络时延分析的有效性.     

Maximum principle for mean-field jump–diffusion stochastic delay differential equations and its application to finance

This paper investigates a stochastic optimal control problem with delay and of mean-field type, where the controlled state process is governed by a mean-field jump–diffusion stochastic delay differential equation. Two sufficient maximum principles and one necessary maximum principle are established for the underlying system. As an application, a bicriteria mean–variance portfolio selection problem with delay is studied to demonstrate the effectiveness and potential of the proposed techniques. Under certain conditions, explicit expressions are provided for the efficient portfolio and the efficient frontier, which are as elegant as those in the classical mean–variance problem without delays.     

带观测滞后和不确定噪声方差的多智能体传感网络鲁棒序贯协方差交叉融合Kalman滤波

针对带观测滞后和不确定噪声方差的分簇多智能体传感网络系统,研究鲁棒序贯协方差交叉融合Kalman滤波器的设计问题.应用最邻近法则,传感网络被分成簇.应用极大极小鲁棒估计原理,基于带噪声方差最差保守上界的最差保守传感网络系统,提出了两级序贯协方差交叉(SCI)融合鲁棒稳态Kalman滤波器,可减小通信和计算负担并节省能量,且保证实际滤波误差方差有一个最小保守上界.一种Lyapunov方程方法被提出用于证明局部和融合滤波器的鲁棒性.提出了鲁棒精度的概念且证明了局部和融合鲁棒Kalman滤波器的鲁棒精度关系.证明全局SCI融合器的鲁棒精度高于每簇SCI融合器的精度且两者的鲁棒精度都高于每个局部鲁棒滤波器的精度.一个跟踪系统的仿真例子证明了鲁棒性和鲁棒精度关系.     

通用循环水冷却器延时关闭控制联动电路设计

目前许多大型仪器的循环冷却水系统，都没有提供相应的自动化延时关闭装置，给工作带来不便。经过分析，将主机供电系统与循环冷却水供电系统进行关联，设计了联动电路，实现了正常关机，循环冷却水系统自动延时20min后关闭。既节约了工作时间，又提高了工作效率。     

具有一步随机时滞和多丢包的网络系统H∞滤波器设计

在网络系统中由于连接传感器和滤波器的网络带宽有限,系统测量数据在传输中会出现随机时延甚至丢失. 本文讨论了具有一步随机时延和丢包的网络系统的H∞滤波器设计问题.基于新近提出的同时描述随机时延和丢包的模型,利用线性矩阵不等式方法设计线性滤波器,使得滤波误差系统均方指数稳定,并具有给定的H∞性能. 滤波器参数通过求解一个线性矩阵不等式得到.仿真研究说明了所提出算法的有效性.     

Delay time compensation based on coefficient of restitution for collision hybrid motion simulator

A hybrid motion simulator embeds a hardware experiment in a numerical simulation loop. However, it is often subjected to the inherent problem of an energy increase in the collision of two pieces of hardware in a loop because of the delay time. This paper proposes a delay time compensation method based on contact dynamics model for a collision hybrid motion simulator under delay time and establishes a compensation method for coupled translational and rotational motion. The model developed in this paper describes linear uniform motion of a floating object during the period of the delay time until the force and torque are observed and non-linear motion according to environmental stiffness after the initial delay time period in contact. By using the above model, compensation parameters are designed based on desired coefficient of restitution with iterative calculation. The proposed method achieves accurate delay time compensation and simultaneously realizes a variable desired coefficient of restitution over a wide range of frequencies. Furthermore, the compensation method for multi-dimensional motion is established under the assumption that the friction effect is very small. The efficiency of the proposed method is verified through collision experiments for the coupled motion in two dimensions.     

A virtual actuator and sensor approach for fault tolerant control of LPV systems

In this paper, a fault tolerant control (FTC) strategy using virtual actuators and sensors for linear parameter varying (LPV) systems is proposed. The main idea of this FTC method, initially developed for LTI systems, is to reconfigure the control loop such that the nominal controller could still be used without need of retuning it. The plant with the faulty actuator/sensor is modified adding the virtual actuator/sensor block that masks the actuator/sensor fault. The suggested technique is an active FTC strategy that reconfigures the virtual actuator/sensor on-line taking into account faults and operating point changes. The stability of the reconfigured control loop is guaranteed if the faulty plant is stabilizable/detectable. The LPV virtual actuator/sensor is designed using polytopic LPV techniques and linear matrix inequalities (LMIs). A two-tank system simulator is used to assess the performance of the proposed method. In particular, it is shown that the application of the proposed technique results in an improvement, in terms of performance, with respect to the LTI counterpart.     

软件定义网络中交换机处理时延的仿真

针对目前的网络仿真工具在对软件定义网络(SDN)的仿真过程中,未考虑交换机的处理时延的问题,提出一种处理时延的仿真方法,目的是为了使仿真结果更加真实和准确。该方法首先将交换机的转发处理过程分解为对流表的查询操作和执行不同的动作;然后,利用交换机的处理器频率和访存周期,将查询流表和执行动作转换为处理时间。实验中测量了真实环境中不同配置的交换机处理时延,并与利用该方法仿真出的处理时延进行对比。实验结果表明,利用该方法仿真出的处理时延和真实交换机的处理时延基本一致,该方法能够较准确地仿真交换机处理时延。